Most aluminium composite panel problems start in the purchase order, not on site. Two panels can show the same 4 mm overall thickness and the same colour on a swatch, and still differ in aluminium skin gauge, core chemistry, coating system and fire classification. One is a compliant facade cassette; the other is a signage board and must never go above a shopfront. This guide sets out what an aluminium composite panel actually is, which numbers decide its performance, how the three core grades differ in fire terms, and where ACP is the wrong choice compared with solid aluminium.
What an Aluminium Composite Panel Actually Is
An aluminium composite panel is a flat sandwich: two thin coil-coated aluminium skins continuously bonded to a thermoplastic or mineral-filled core. The skins carry the finish, the weather face and the coating system. The core supplies the stiffness that lets a 0.5 mm skin behave like a flat sheet, and it decides almost everything about how the panel performs in a fire.
In a 4 mm panel the two skins together are about 1 mm and the core is about 3 mm. The skins are broadly the same across every grade on the market — 3000 or 5000 series aluminium, half-hard temper. What separates a restricted panel from a compliant one is the composition of the middle 3 mm. The name varies by market: ACP in the UK, Australia and Asia, ACM in North America, and trade names such as Alucobond in project documents.

Skin Thickness: The Specification Buyers Get Wrong
Individual skin thickness is the single most under-specified number in this category, and it is where cost is most often taken out quietly. Industry skins run from 0.20 mm to 0.50 mm per face. Common gauges are 0.21 mm, 0.30 mm, 0.40 mm and 0.50 mm.
- 0.20–0.21 mm skins — interior signage, light partitions, short-life display. Not a facade product.
- 0.30 mm skins — economy architectural cladding at low height; acceptable on low-rise work where wind load is modest.
- 0.40–0.50 mm skins — standard architectural cladding; the practical choice for anything above roughly 11 m, where national regulations commonly require 0.50 mm skins.
A panel with 0.30 mm skins is frequently offered as an equivalent to a 0.50 mm product at lower cost. It is not equivalent: the skins take the wind load, the fixing loads and the impact, so a 40% reduction in skin gauge is a 40% reduction in the material doing that work. The specification line to write is skin thickness, not only total panel thickness.
Core Grades: PE, FR and A2 — and What Each One Allows
The core is the part that decides fire classification, and the three grades are genuinely different materials rather than marketing tiers.
- PE core — unmodified polyethylene at roughly 920–950 kg/m³, igniting at about 340 °C with a calorific value near 43–46 MJ/kg. Under EN 13501-1 a PE-core panel typically reaches Euroclass E only, and after the Grenfell fire the UK Building Safety Act, the Australian NCC amendments and a growing list of EU and Gulf requirements effectively exclude it from external cladding above defined heights.
- FR core — polyethylene with roughly 70% mineral filler by mass. It tests as B-s1,d0 or equivalent and is the workhorse for facades with a fire requirement at sensible cost: fire retardant, not non-combustible.
- A2 core — around 90% mineral filler, achieving A2-s1,d0 where the specific panel has been tested. The grade to specify where limited combustibility is demanded, and heavier and more expensive accordingly.
Any claim about fire performance has to name a classification standard and a tested panel, not a description. Ask for the test report for the exact product being supplied, not for the family.
Standard Dimensions, Tolerances and Weights
The ranges below are what our lines run; values are typical and confirmed against the approved order specification.
| Property | Range | Notes |
|---|---|---|
| Overall thickness | 3 mm, 4 mm, 6 mm (2–6 mm on request) | 4 mm is the default for facade cassettes |
| Skin thickness | 0.20–0.50 mm per face | 0.50 mm above roughly 11 m height |
| Width | 1000 / 1220 / 1250 / 1500 mm | 1220 mm matches the 4 ft module |
| Length | 2440 / 3050 / 3660 mm, up to 5000 mm on request | Cut to order, ±3 mm |
| Thickness tolerance | ±0.20 mm at 3–4 mm, ±0.25 mm at 5–6 mm | Skin tolerance ±0.03 mm |
| Weight, PE core | About 5.5 kg/m² at 4 mm | 4 × 0.30 mm skins about 5.3 kg/m² |
| Weight, FR / mineral core | About 6.7–8.0 kg/m² at 4 mm | Mineral filler raises core density |
| Flatness | Bow 1.5 mm per 1000 mm, twist 3 mm per diagonal | Reject beyond tolerance, do not install |
Coating Systems: PE versus PVDF
Coating is the second place where a quotation can look cheap and behave badly. A PE (polyester) coating costs less and performs accordingly: colour moves and chalk develops within a few years on a south-facing elevation. PVDF at 25–35 microns, over a primer on coil-coated aluminium, is the exterior standard and is what colour warranties are written against; FEVE sits alongside it as a fluoropolymer option. The question at quotation stage is not the coating name but the film build and the colour-retention data for that specific finish — metallic and dark colours run hotter, which affects both coating life and panel movement.
Fabrication: Routing, Folding and Cassette Fixing
ACP is fabricated in a sign shop or a facade workshop with ordinary tooling: panels are routed on the back face to leave the skin intact, folded to form a return, and fixed into cassettes or trays on an aluminium sub-frame. Cut edges must be trimmed square and the exposed core sealed with a matching trim, because an open core edge takes in water and the bond line behind it fails slowly rather than immediately. Two limits are worth repeating in the workshop: do not over-route past the skin, and do not fix a panel rigidly at every point — ACP moves with temperature, and a cassette that cannot move will bow, oil-can at the fixings, or open a joint within a season.

Where ACP Works — and Where It Should Not Be Used
Being direct about the boundaries is more useful than a benefits list. Aluminium composite panel is a good answer where flat colour, light weight and fast fabrication matter. It is the wrong answer on several specific duties.
- Shopfronts, canopy fascias and signage — the clearest fit. Fast to fabricate, available in matched colours, and light enough to fix on a simple frame.
- Low and mid-rise facade cladding with an FR or A2 core — panels give a flat, jointed elevation at a fraction of the weight of stone or solid aluminium.
- Interior linings, columns and furniture — flat panels take a coating well and hide fixing behind the cassette.
- Not with a PE core above restricted heights — the regulations in most mature markets now exclude it from external cladding, and specifying it there is a compliance failure, not a saving.
- Not where flatness must be absolute — solid aluminium sheet holds a flatter face over long spans; composite panels can telegraph sub-frame lines and oil-can under heat.
- Not as a structural or impact surface — ACP is a cladding, not a load-bearing element, and it dents under impact where solid plate would deform less.
Compared with solid aluminium, ACP gives lower weight, lower material cost and easier folding — but it gives away flatness, screw-holding at edges and service life. On a high-specification prestige elevation, solid aluminium or a terracotta or stone system is the better material, and we will say so.
Customisation, Colour Range and Supply Scope
Because the panel is laminated and coil-coated in-house, colour, size and coating are set per order within the line’s practical range:
- Colour — solid, metallic, wood-effect and stone-effect finishes, matched to RAL or Pantone references, with a stock range plus project matching.
- Dimensions — cut to cassette size from stock sheet, with the cutting plan set against the shop drawings so offcut waste stays low.
- Coating — PE for interior and short-life work, PVDF at 25–35 microns for exterior facades.
- Protective film — peel-off film on the visible face, with a clear instruction to remove it within the stated window; film left on a sun-facing panel bakes onto the coating.
- Packing — export pallet with corner protection and interleaving, sized to load alongside polycarbonate and interior board lines in a 20 ft or 40 ft container.
Manufacturing and Quality Control
Jietai is a manufacturer of aluminium composite panels, PVC sheets and polycarbonate sheets, not a reselling agent. Panels are laminated on our own lines and every batch is checked before packing: total thickness against nominal, skin gauge after lamination, bond strength, flatness, coating film build and colour against the approved sample. Bond strength is the check that matters most and the hardest to see on delivery — a delaminated panel looks sound until it is folded or the sun reaches it. Because the same plant runs the polycarbonate and interior board lines, a mixed project package ships in one container on one set of documents, with third-party inspection before shipment and batch reports including skin gauge and coating thickness.
Frequently Asked Questions
What is the difference between 3 mm and 4 mm aluminium composite panel?
Total thickness sets stiffness and core depth, while skin gauge sets strength where it is fixed. 3 mm panels go into signage and interior work; 4 mm is the facade standard because it holds a flatter face across a fixing grid. In practice skin thickness matters more than the 3 mm versus 4 mm choice.
Can PE core ACP be used on a building facade?
Not on external cladding above the restricted heights set by most national regulations, and not on high-rise work at all: PE-core panels reach Euroclass E only. Use an FR core for facades with a fire requirement and an A2 mineral core where limited combustibility is demanded.
How much does an aluminium composite panel weigh?
About 5.5 kg per square metre for a 4 mm PE-core panel, and roughly 6.7 to 8 kg per square metre at the same thickness with an FR or mineral core, because the filler raises core density. Solid aluminium plate is several times heavier at equivalent stiffness.
How long does the colour last?
PVDF at 25–35 microns is the exterior standard and is what colour warranties are written against. PE-coated panels are interior and short-life products, and a dark PE finish on a sun-facing elevation shows change within a few years. Film must come off within the stated window after installation.
How is ACP cut and fixed?
Panels are routed on the back face, folded to form a return, and fixed as cassettes to an aluminium sub-frame with the core edge sealed by a trim. Fixings must allow thermal movement; do not over-route past the skin and do not fix rigidly at every point.
Getting the Aluminium Composite Specification Right the First Time
Almost every ACP failure traces back to one of three specification gaps: total thickness named without skin thickness, a core grade chosen for cost rather than for the fire requirement, or a coating specified by colour instead of by film build. All three are settled at quotation stage and expensive to correct after the container has shipped.
If you are sourcing aluminium composite panels for a facade, shopfront or interior package, send four details — the application and height above ground, the panel size and skin thickness you have in mind, the quantity, and the destination port. We come back with the core grade, skin gauge and coating recommendation that fits the exposure, a loading estimate, and comparable project references. Where the elevation demands a flatter or longer-life face than a composite panel can give, we say so and quote the alternative.
Two related references are worth reading before finalising a specification: the polycarbonate sheet fire rating guide, which explains how B1 and UL 94 V-0 classifications are actually tested and what they do and do not promise, and the installation accessories reference, which covers the aluminium profiles, gaskets and fasteners that facade and canopy systems depend on.
Need an aluminium composite panel specification for your project? Request a core and skin recommendation.
Tell us the application, height above ground, panel size, quantity and destination port. We reply with a core grade, skin thickness and coating recommendation, plus a loading estimate and comparable references — not just a price.