Acrylic sheet is chosen for one property above all others: optical clarity. At 92% light transmission it is the clearest sheet material in common use, it holds that clarity outdoors for a decade or more, and it can be polished back to a clean edge after cutting. What it cannot do is take an impact — acrylic is brittle, and that single limitation decides most of the applications it is and is not used for.
Request a Quote Ask for Free Samples

This page covers the cast and extruded difference, thickness selection, the comparison with polycarbonate that most buyers actually need, and the fabrication and cleaning rules that decide whether the sheet survives its first year. Grades, forming temperatures and application rules are covered in the acrylic sheet specification guide, and everything published on this range is indexed in the acrylic sheet articles.
Acrylic Sheet Specifications
Range at a glance
| Material | Cast PMMA and extruded PMMA |
|---|---|
| Cast thickness | 1.5 – 50 mm (to 100 mm on request) |
| Extruded thickness | 1.5 – 25 mm |
| Sheet size | 2050 × 3050 mm cast; 2050 × 3050 mm extruded; cut to size |
| Light transmission | 92 % clear |
| Density | 1.19 g/cm³ |
| Service temperature | −40 to +80 °C |
| Thermal forming | 150 – 180 °C |
| Impact | Brittle; cracks and splinters under sharp impact |
| Chemical resistance | Poor to solvents, alcohols and ammonia — stress cracks |
| Colours | Clear, opal, black, bronze, and 40+ standard colours |
| Standard | EN ISO 7823 for cast and extruded PMMA sheet |
| Minimum order (MOQ) | 1 × 20GP container — mixed sizes, colours and thicknesses accepted |
Cast and Extruded Acrylic Are Not the Same Sheet
Both are PMMA, both are clear, and they are sold at different prices for reasons that matter in service:
| Property | Cast acrylic | Extruded acrylic |
|---|---|---|
| Thickness range | 1.5 – 50 mm | 1.5 – 25 mm |
| Optical quality | Best; no orientation | Very good |
| Thickness tolerance | ± 10 to 15 % | ± 5 % |
| Solvent resistance | Better | Poor; stress cracks easily |
| Polishing the edge | Polishes back to full clarity | Limited; can smear |
| Thermal forming | Slow, needs even heating | Faster cycle |
| Cost | Higher | Lower |
| Typical use | Displays, light boxes, aquariums, furniture, signage that must last | Batch-produced signs, partitions, formed components |
The practical rule: if the edge will be visible and polished, if the sheet is thick, or if it will be cleaned with anything other than soap and water, specify cast. Extruded is the right answer for volume signage and formed parts where the sheet is thin and the cost is the driver.
Thickness and What Each Range Does
- 1.5 – 2 mm — signage faces, display covers, picture framing, machine windows.
- 3 mm — the general-purpose display and partition thickness; light boxes, retail POS, protective covers.
- 4 – 5 mm — larger display panels, secondary glazing, furniture fronts, sneeze guards.
- 6 – 10 mm — aquariums, heavy display cases, illuminated signage, bar tops and furniture.
- 12 – 25 mm — thick aquarium walls, sculptural and architectural work, machined components.
- 30 mm and above — cast only; specialist architectural and display use.

Acrylic vs Polycarbonate: The Choice That Matters
This is the comparison most buyers actually need, because the two are visually similar and behave completely differently in service:
| Property | Acrylic (PMMA) | Polycarbonate (PC) |
|---|---|---|
| Light transmission | 92 % | 88 – 91 % |
| Impact | Brittle; cracks and splinters | Very high; flexes and does not shatter |
| Scratch resistance | Better | Moderate; hard coat available |
| Optical clarity over time | Holds for years outdoors | Holds if the UV layer is intact |
| Service temperature | −40 to +80 °C | −40 to +120 °C |
| Forming | Needs slow, even heat | Cold bends easily |
| Chemical resistance | Poor to solvents and alcohols | Poor to alkalis and solvents |
| Where it belongs | Displays, light boxes, aquariums, furniture | Guards, roofing, security, machine windows |
The decision is almost always about impact. Anywhere a person could fall against it, throw something at it, or where breakage is a safety issue, polycarbonate is the correct material even though acrylic looks better. Anywhere the surface is looked at rather than hit, acrylic gives the better optical result. The full comparison, including glass, is in polycarbonate glazing compared with acrylic and glass.
Fabrication, Forming and Bonding
- Sawing and routing. Standard woodworking tools work, but the blade must be sharp and the feed steady; acrylic chips and can crack along a scribed line if forced.
- Drilling. Use a slow speed with a brad-point bit, clear the swarf, and drill oversize — the sheet expands about 0.07 mm per metre per degree.
- Polishing. Sand progressively then polish; cast acrylic returns to full optical clarity, extruded does not.
- Thermal forming. 150 to 180 °C for bending and drape forming. Heat must be even or the sheet blushes and stress-cracks later.
- Bonding. Solvent cements such as dichloromethane weld acrylic to itself; the joint is clear and strong but the solvent must be applied sparingly.
- Annealing. Machined or formed cast acrylic benefits from annealing at about 80 °C to relieve stress — skipping this is a common cause of later crazing.
The Cleaning Rule That Saves the Sheet
Most acrylic failures we hear about are not manufacturing faults. They are cleaning damage:
- Never use alcohol, ammonia-based glass cleaner or solvent wipes. These attack the surface and cause crazing — a network of fine cracks that appears days later and cannot be polished out.
- Use mild neutral detergent, water and a soft cloth, then rinse and dry with another soft cloth. A dry cloth on a dusty surface scratches.
- Never wipe a dry surface. Dust is abrasive; wipe with plenty of water.
- Keep the protective film on until installation is finished, and remove it within the recommended period — film left in sun bakes on.
Supply, Colours and Container
- Formats. Standard sheets plus cut-to-size, polished-edge and CNC-machined parts.
- Colours. Clear, opal, black, bronze and a wide standard colour range; custom matching on volume.
- Packing. Both faces filmed, interleaved, crated with edge protection. Acrylic scratches in transit more easily than polycarbonate, so the packing is not a detail.
- Thickness tolerance. Note that cast acrylic varies ±10 to 15 % on thickness by nature; where the thickness is critical, specify extruded.
Where We Are Honest About the Limits
- It breaks. Acrylic is brittle and, unlike polycarbonate, does not flex. Wherever impact or vandalism is a realistic risk, acrylic is the wrong specification and we will say so before quoting.
- Solvents destroy it. Alcohol-based sanitisers, ammonia glass cleaner and solvent adhesives all cause crazing. In healthcare, food service and any environment with routine disinfectant wiping, this has to be checked before the material is chosen.
- 80 °C is the ceiling. Acrylic softens well below polycarbonate’s range, so it is not for hot enclosures, roof glazing or anywhere near a heat source.
- Cast thickness is not exact. ±10 to 15 % is normal for cast sheet. If a tight thickness is a functional requirement rather than a habit, extruded is the correct specification.
- Outdoor life is good but not infinite. Acrylic resists UV far better than most plastics, but it does chalk and embrittle over long outdoor exposure, and the surface yellows slowly.
More on Acrylic Sheets
Grades, forming temperatures, annealing schedules and application rules are covered in the acrylic sheet specification guide, and everything published on this range is indexed in the acrylic sheet articles. If you are deciding between acrylic and polycarbonate for a specific job, send the application and the environment — we will tell you which one survives it.
Acrylic Sheet: Common Questions
Cast acrylic is made in moulds, has the best optical quality, holds ±10 to 15 percent thickness, resists solvents better and polishes back to full clarity. Extruded acrylic is cheaper, holds tighter thickness tolerance at ±5 percent, but stress-cracks more easily and cannot be polished back the same way.
No, the opposite. Polycarbonate resists impact without breaking while acrylic is brittle and can crack or splinter. Acrylic wins on optical clarity and scratch resistance, which is why it is used for displays rather than protective glazing.
No. Alcohol, ammonia-based cleaners and solvent wipes cause crazing, which appears as a network of fine cracks and cannot be polished out. Use mild neutral detergent with plenty of water and a soft cloth, and never wipe a dry dusty surface.
About 80 degrees C in continuous service, well below polycarbonate at 120 degrees C. It is not suitable for roof glazing, hot enclosures or anywhere near a heat source.
Solvent cements such as dichloromethane weld acrylic to itself and give a clear, strong joint. Machined and formed cast acrylic should be annealed at around 80 degrees C afterwards to relieve stress, otherwise it can craze later.
Much less than most plastics, and it holds clarity for a decade or more in normal outdoor exposure. It does still chalk and embrittle slowly over long periods, so it is not a permanent material like glass.
Send your thickness, colour and quantity for a quotation
Send us these four details and we will come back with a landed cost:
- Sheet type and thickness
- Size and quantity
- Application (roof / skylight / partition...)
- Destination country or port