✓ ISO 9001 Certified Factory ✓ CE Certified / SGS Tested ✓ Ships Worldwide ✓ Free Samples Available
Get a Quote

SPC Flooring

SPC flooring is a rigid-core plank: a stone-plastic composite core, a printed decor film, a transparent wear layer and usually an attached underlay. It is installed as a floating click-lock floor over a flat substrate with no adhesive, it is waterproof through the core rather than just on the surface, and it does not expand and contract the way laminate does. The specification that decides how long it lasts is the wear layer thickness, not the core.

Request a Quote Ask for Free Samples

Rigid core SPC flooring planks laid in a room with a wood decor

This page covers the wear layer question, thickness build-up, how SPC compares with laminate, LVT and tile, substrate requirements and what to specify for a quotation. Core construction and wear layer grading are covered in the SPC flooring specification guide, and everything published on this range is indexed in the SPC flooring articles.

SPC Flooring Specifications

Range at a glance

Total thickness4 / 5 / 6 mm including wear layer and underlay
Wear layer0.3 mm domestic, 0.5 mm commercial, 0.7 mm heavy commercial
Plank size1220 × 180 mm, 1220 × 228 mm, 1500 × 230 mm
CoreCalcium carbonate and PVC rigid composite
UnderlayIXPE or EVA attached, 1 – 1.5 mm
JointClick-lock, floating installation, no adhesive
WaterWaterproof core; joints sealed where standing water is expected
Underfloor heatingSuitable with the correct grade and a controlled ramp rate
Service temperature−20 to +60 °C
FireB1 on specified build-ups
CleaningDamp mop, neutral detergent; no steam mop
Minimum order (MOQ)1 × 20GP container — mixed colours and specifications accepted

The Wear Layer Decides the Life, Not the Thickness

A “5 mm SPC” can carry a 0.3 mm wear layer or a 0.7 mm one, at very different prices, and the wear layer is what the traffic actually touches:

Wear layerRatingWhere it belongs
0.3 mmDomesticBedrooms, living rooms, low-traffic housing
0.5 mmCommercialOffices, retail, hospitality rooms, schools
0.7 mmHeavy commercialPublic buildings, corridors, high-footfall retail

Total thickness does matter, but for a different reason: it decides how forgiving the floor is over a slightly imperfect substrate and how solid it feels underfoot. A 6 mm plank hides more subfloor deviation than a 4 mm one. Buying thickness while accepting a thin wear layer is buying the wrong property.

SPC vs Laminate vs LVT vs Tile

PropertySPCLaminateLVTCeramic tile
WaterWaterproof coreSwelling at edges; not waterproofWaterproofWaterproof with correct substrate
Dimensional stabilityVery good; rigid coreMoves with humidityGood; flexibleStable
Underfloor heatingSuitable, controlled rampLimitedGoodGood, slow response
Feel underfootHard and solidHard, hollowSofter, warmerCold and hard
InstallationFloating click, no adhesiveFloating clickClick or glue-downWet trade, adhesive bed
Removal and reuseReusable if undamagedReusableClick reusable, glue-down notDestructive

The distinction that is usually misunderstood: SPC is waterproof because the core does not absorb water, while laminate is moisture resistant at best and swells at the joint. In a bathroom, kitchen or basement, that is the whole argument. Where a softer, warmer floor is wanted and water is not a risk, LVT is often the better feel.

SPC flooring installed in a herringbone pattern

Substrate and Installation Rules

  • Flatness governs the result. Typically within 3 mm over 2 m. A rigid plank over a hollow will click, flex and eventually break the joint — the floor does not hide a bad screed, it amplifies it.
  • Floating, not fixed. Planks are not glued down and must be free to move. A 5 to 10 mm expansion gap at every perimeter, hidden by skirting, is standard.
  • Underlay. An attached IXPE or EVA pad saves a separate layer; a separate underlay is used where acoustic performance or a vapour barrier is required.
  • Vapour barrier over a concrete slab. A rigid core is waterproof, but moisture from below still has to be controlled, and on a new screed the residual moisture has to be checked before installation.
  • Door heights. Adding 5 to 6 mm plus underlay changes floor levels. Check thresholds and door undercuts before ordering.
  • Underfloor heating. Suitable with the correct grade, but the ramp rate has to be controlled and the surface temperature capped; sharp temperature swings warp any rigid plank.

Supply, Packing and Container

  • Decors. Wood grains, stone and marble effects in a wide range; batch matching on volume and one batch per room.
  • Trims. Skirting, reducers, stair nosings and end caps in the same decor — specify them with the floor.
  • Packing. Heavy relative to its bulk: SPC normally weighs out before it cubes out, unlike most interior panel products.
  • Spares. Hold 3 to 5 % in the same batch; a later production run will not match exactly, and a patch in the middle of a floor is visible.

Where We Are Honest About the Limits

  • It is hard and it sounds hard. A rigid core transmits impact sound. In an upper-floor apartment the acoustic underlay is not optional, and in a quiet residential building an acoustic test may be required.
  • A thin wear layer is a short-life floor. 0.3 mm in a commercial corridor is the wrong specification at any price. The wear layer, not the total thickness, is what a buyer should be checking.
  • It does not forgive the substrate. Unlike a flexible LVT, a rigid plank will rock and fail at the joint over a hollow. Levelling is part of the job, not an optional extra.
  • Waterproof floor, not a wet room. Standing water at an unsealed perimeter, or a leak underneath, still causes problems. Sealed joints and a proper perimeter detail are needed in bathrooms.
  • No steam mops. Heat and moisture forced into the joints degrade them. Damp mopping with neutral detergent is the correct maintenance.
  • Colour and pattern vary between batches. Printed decors differ slightly run to run, and on a continuous floor that shows.

More on SPC Flooring

Core construction, wear layer grading and the substrate requirements are set out in the SPC flooring specification guide, and everything published on this range is indexed in the SPC flooring articles. Send the room, the area, the traffic level and whether there is underfloor heating, and we will confirm the wear layer and thickness before quoting.

SPC Flooring: Common Questions

0.3 mm for domestic rooms, 0.5 mm for commercial spaces such as offices, retail and hospitality, and 0.7 mm for heavy commercial and high-footfall public areas. The wear layer decides the life of the floor far more than the total plank thickness.

Yes, the rigid core does not absorb water, which is what separates it from laminate that swells at the joints. Where standing water is expected, seal the perimeter and joints properly, because a waterproof plank with an open edge is not a waterproof floor.

Yes with the correct grade, provided the ramp rate is controlled and the surface temperature is capped. Sharp temperature swings will warp a rigid plank, so the heating control matters as much as the product.

Typically within 3 mm over 2 metres. A rigid plank over a hollow will rock, click and eventually break the joint, so levelling is part of the installation rather than an optional step.

No, it is a floating click-lock floor with a 5 to 10 mm expansion gap at every perimeter, hidden by skirting. It can be lifted and reused if the planks are undamaged.

No. Forced heat and moisture degrade the click joints. Damp mopping with a neutral detergent is the correct maintenance, and abrasive or solvent cleaners should be avoided.

Send your area, traffic level and whether there is underfloor heating

Send us these four details and we will come back with a landed cost:

  1. Sheet type and thickness
  2. Size and quantity
  3. Application (roof / skylight / partition...)
  4. Destination country or port

Related Articles

Questions about specs or pricing? Chat with us 👋